Cadillac 2007 Escalade Manual de instalación

Video Interface for Cadillac Escalade EXT, ESV, Hybrid, SUV, Cadillac STS, SLS 2007-2012 Installation Manual Release date : 2011.09.19 Model : CSVI-E

2.3 Main Cable Pinout (view from wire side) www.car-solutions.com 10 Contact # Contact purpose 1 POWER ACC +12V DC INPUT 2 GND VIDEO OUT 1 3 GND V

2.4 USB Touch Screen Controller www.car-solutions.com 11 This USB touch screen controller fits for connection only to Car PC with 95, 98, XP, Vista 3

2.5 OSD Menu (On Screen Display) www.car-solutions.com 12 PICTURE MENU (image adjustment) In this menu you can adjust the following image par

2.5.1 OSD menu (On Screen Display) www.car-solutions.com 13 PC SETUP MENU In this menu you can adjust following image parameters for VGA inpu

2.5.2 OSD menu (On Screen Display) www.car-solutions.com 14 SOURCE CONTROL MENU continuation Rearview – input for rear view camera. I

3.1 Connection to Monitor without Compact Flash Card www.car-solutions.com 15 Here you can see monitor from cars of 2006-2009 model years. In these mo

www.car-solutions.com 16  Carefully dismantle plastic frame fixed by detents on the edges. Pull off the frame for ~5 cm and turn it with your left h

3.1.2 Connection to Monitor without Compact Flash Card www.car-solutions.com 17  Carefully pull on LCD panel for few centimeters and move it down for

3.1.3 Connection to Monitor without Compact Flash Card www.car-solutions.com 18  Remove touch screen panel FFC and LCD FFC from the socket. Plea

3.1.4 Connection to Monitor without Compact Flash Card www.car-solutions.com 19  Install video interface main board as shown in the picture. Note! Co

Contents www.car-solutions.com 2 1. Before installation 1.1 Precautions 1.2 Main specifications 1.3 System diagram 1.4 Components 1.5 Exterior 4

3.1.5 Connection to Monitor without Compact Flash Card www.car-solutions.com 20  Connect main cable and USB touch screen controller cable to video in

3.1.6 Connection to Monitor without Compact Flash Card www.car-solutions.com 21  Connect narrow FFC (often it’s brown) from OEM touch screen panel to

3.2 Connection to Monitor with Compact Flash Card www.car-solutions.com 22 Here you can see monitors from cars of 2009-2012 model years. In these moni

3.2.1 Connection to Monitor with Compact Flash Card www.car-solutions.com 23  Twist off screws holding metal plates on both sides.  Rem

3.2.2 Connection to Monitor with Compact Flash Card www.car-solutions.com 24  Carefully dismantle plastic frame holding LCD panel.  Be

3.2.3 Connection to Monitor with Compact Flash Card www.car-solutions.com 25  Connect display main board and «FROM CAR SYSTEM» video interface

3.2.4 Connection to Monitor with Compact Flash Card www.car-solutions.com 26  7 Connect LCD panel OEM wide flat cable to wide «TO LCD PANEL» socke

www.car-solutions.com 27 Q. I cannot switch A/V sources. A. Check main cable connection. Check whether main cable and/or mode switch remote button cab

1.1 Precautions www.car-solutions.com 3  Ignition key should be taken off before starting installation, interface power connection must be the last s

1.2 Main Specifications www.car-solutions.com 4 1. Inputs - 1 x Video DATA (OEM video input from vehicle main PCB) - 1 x Analog RGBCs (for nav

1.3 System Diagram www.car-solutions.com 5 MCU MUX ADC To main PCB of monitor (connect by offered FPC cable) To USB touch controller To OEM touch scr

1.4 Components www.car-solutions.com 6 Video interface main board x 1 pc. IR Remote controller x 1 pc. IR receiver x 1 pc. USB touch controller x 1 pc

www.car-solutions.com 7 1.5 Exterior ① Main cable input (Power, RGB, VGA, AV1, AV2, REAR-C, AV OUT, IR receiver, mode switch button ) ② TO LCD PANEL

2.1 Remote Controller www.car-solutions.com 8 Buttons Function Power, 0-9, Mute, DMB/DAB NOT USED Factory reset – press 2 sec. SOURCE, MODE Source

2.2 How to Use Mode Switch Button www.car-solutions.com 9 MODE SWITCH BUTTON PRESSING  If you press the button video source will be changed. HOLDING